Router Table - How to Use

They want to know how a router table? Here are some tips to get the best of your router table.

You do not need a channel of gunfire. Typically, you push your activities along the fence. If you use a miter channel, then the fence must be square to the miter channel. Why are you going to undertake this effort?

You can slide a stencil on the fence. This automatically sets the forest to get a square cut too much. It is also possible adjustments in the profile and the depth of cut. A router lift makes this easy.

Quality --Router Table Fence Dust easier. Using the router table and fence for the ease and simplicity!

You should not use his work between the fence and the router. This is only to bring trouble.

As a general rule, move the wood from right to left (if any) on the opposite wall. This is a pie-cut. They make almost all the cuts in this way.

If to be very careful, you can walk a short distance in the opposite direction. But you must hold tight to avoid a backlashand / or injury. This results in cutting edges clean, but you should only try after a lot of experience.

Only less than 15% of your work in this way. It should be flat or only minor cuts. DO NOT TAKE large cuts. Do so only if the hands are protected from cutting.

As the center of a router table edge-to-edge joints:

Have you ever wondered how the center-edge-to-edge connections? Using this technique for the production of solid tops, wide boards, oreven go to the table edge router.

Let is a real example of a top edge of oak MDF router table, the top 1 1 / 8 "thick. The oak edge is equal to 1 1 / 8" thick.

How can we ensure a center-edge?
Decide the size of language. They have a 1 / 4 "slot cutter. They want the language of a thickness less than twice the cut. Therefore, the thickness of the tongue is a little 'less than 1 / 2". We use a 1 / 4 "depth of cut for this example.

We want a language that is less than 1 / 2 "Thick. Therefore, we know that the groove is on the table just over 5 / 16 "on both sides of a 1 1 / 8" thick pieces.

Top groove with a groove to produce a little 'with a 1 / 4 of' groove. They do not take too much during the first pass. Therefore, the depth of cut for 1 set / 8 "for the first step - it is.

Set the fence so it is with the attitude of bits groove.

Cut off top and bottom from the top. Take your time and go around the whole way. Make sure that the pieceapartment Router Table Top or use the router on the piece.

Measure the thickness of the tongue. If greater than 1 / 2 "together, then the depth of cut. A router lift makes this easy.
Note: Escape from both sides, to use half of
Adjustment for each page.

Make your attitude, the flight up and down again. The tongue is thick, has been slightly reduced
1 / 2 ".

Replace the fold something wrong with the 1 / 4 "slot cutter.

I always unplug thePower source to the router before changing bits!

Rabbeted Put the pieces on the table next to the router cutter slot. Raise the router so that the bottom slot of the cutter is in line with the underside of the tongue. You may need the support, if the piece is large.

Adjust the depth of cut for the slot about 3 / 16 "in the first place. Now the slot edge of oak. Slot and turn it over again. Try the crack on the tongue. It 'is too narrow and if so, remember that are two passes with the slotter. only the lowerSlot Bit 1 / 2 the size required. Among other things, makes the Porter-Cable 7518 router is a breeze.

Since the slot is cut 1 / 4 ", is running second, not with all the boats. You can get a slot to fit the exact center on the tongue.

After the slot (groove), insert the language, you are ready to set the final depth of the groove. The final depth of cut that allows a little 'more than 1 / 4 "for the glue.

Make your fence for the final depth. I remember - a walk with the slotter. Thisgives an accurate measure.

You can use this method for every edge-to-edge joinery, such as tables, plates, large drawer fronts, and every time you want to connect two pieces. You get a perfect alignment and a rock-solid joints.

If you want to see how it looks after the glue-up, please visit the Router Table Top

To make your router lift, go make an easy-to-Router Lift

For more information about using the router table, including images and suggestions, visit How to useRouter Table

http://buycoffeetable.postblog.net Garden Blower | All about of Garden Blowers flatware1810